Binding method of car tarpaulin

The tarpaulin should be tied in the following ways: 1) The tarpaulin rope should be tied to the truck rope, and must not be tied to other parts. 2) The tarpaulin corner ropes at both ends of the truck are interspersed along the end wall of the truck and then tied to the two ropes at the end of the vehicle respectively. When the angle rope passes through the brake platform of the human brake of the truck, it should pass above it; when it passes through the brake lever and the hook lever, it should pass through the inner side. 3) The two end ropes in the center of the tarpaulin at both ends of the truck are respectively pulled vertically downward and fastened to the two ropes at the end of the vehicle. When passing the hook rod, they should also pass through the inner side. 4) The pressure rope at each end of the tarpaulin should be pressed against the corners of the tarpaulin, so that the tarpaulin is close to the end wall of the vehicle, and should be tied to the first rope on the side of the vehicle, and must not be tied to the towing hook. superior. 5) The waist rope should be pulled straight and tied on the side rope of the car. The stretched length of the elastic part of the elastic rope shall not be less than 200mm, which shall be confirmed in detail according to the condition of the loaded goods. If there is a rope in the center of the vehicle, the waist rope in the center is tied to the rope in the center of the vehicle; if there is no rope in the center of the vehicle, the waist rope in the center of the tarpaulin is separately tied to the rope close to the center of the vehicle. Other waist ropes, starting from the two ends of the vehicle, toward the middle of the vehicle, are tied to the corresponding ropes in sequence. When the elastic rod is not close to the eye rim, the elastic rope should be collected from the center, and the excess rope in the center should be folded and tied with two dead knots. 6) The tarpaulin rope is tied by the bow knot method or the back-knot method. The rope end after tie-up should be wound around its own rope rod, and at least two dead knots should be tied. The length of the head and tail of the rope shall not exceed 300mm and shall not be shorter than 100mm. 7) Except for the tarpaulin's own rope and tarpaulin rope net, no other ropes shall be used to bind the tarpaulin. 2.3.5 When covering the tarpaulin rope net, the net should be covered upright, the mesh should be completely opened, and it should be closely attached to the tarpaulin. First tie the knots from both sides of the vehicle, so that the tarpaulin rope net completely covers the tarpaulin, and finally tie the knots at both ends of the vehicle. The binding of the tarpaulin rope net and the truck shall be handled in accordance with the binding requirements of the tarpaulin and the truck. 2.3.6 The tarpaulin rope and the rest of the tarpaulin rope net must be reinforced with rope clips. When in use, pull the knotted rope tail tightly to the rope rod, with the symbol surface printed on the head of the rope clip and the tooth surface facing the outside, 50mm away from the rope tail, pass the lock rope around the rope tail and the rope rod and then remove it from the rope. The bottom of the locking rope slot goes out upward, and pulls it in the direction of the locking rope slot, and engages the locking teeth on the end of the locking rope with the teeth on the pressing block. At this time, the rope clip enters the locking working state. When opening, pull the lock rope in the opposite direction of the slot, the rope head is broken along the cracked groove, and the rope clip can be opened. Check after the car tarpaulin thatch cover 1) The tarpaulin thatch cover is flat, the goods are not exposed, the corners at both ends are closely attached, and the lines on both sides are smooth. Each part does not exceed the limit. 2) The rope is tied and tied in the correct direction, the rope is strong and strong, and there is no looseness and falling. The rope tied to the rope is in a butterfly-wing knot, and the length of the head and tail is 100~300mm. 3) The tarpaulin at one end of the truck manpower brake hangs down to cover the end plate with a length of 300mm to 500mm. The brake disc of the truck's manual brake is exposed, which does not affect the use of the manual brake and hook lever. The sagging height of the other end is about 600mm. When the tarpaulin is too long, this restriction can be exceeded, but the use of the pressing rope shall not be affected. 4) The sagging height of the tarpaulins on both sides of the vehicle is the same. 5) After the tarpaulin (including the tarpaulin rope net) is covered, the loading unit will take a picture of both sides of the vehicle (including the tarpaulin number) and the state of the tarpaulin on both ends, and keep it for 3 months.

If you are looking for convenient, affordable , LINYANG brings plethora of options to suit your requirements and budget both. Check LINYANG PVC Tarpaulin Film for more details.

is making its name in professional pvc plastic film all over the world, and with ZHONGSHAN LINYANG PLASTIC CO.LTD taking great care to make an excellent product & actively involved in keeping the industry well-regulated, it's a product that should make its way into your clear pvc film.

ZHONGSHAN LINYANG PLASTIC CO.LTD, a manufacturer of PVC Film, might emphasize less hassle or less wasted time rather than emphasizing reliability or quality.